What is an inductor?
Energy stored in a magnetic field
An inductor is a passive component, usually a coil, that stores energy in a magnetic field and opposes changes in current: . The stored energy is . In an RL circuit the current rises with the time constant , and the core saturates above the saturation current.
More about this simulator
Impedance and where it is used
An ideal inductor has impedance 2πfL, which grows with frequency: the opposite of a capacitor, it passes DC and resists high frequencies. Real inductors have winding resistance and parasitic capacitance, so above a self-resonant frequency they stop behaving inductively. Inductors store energy in buck and boost converters, filter noise in supply lines and EMI chokes, form tuned circuits with capacitors in radios, and are the basis of transformers and relays. Run a hands-on inductor simulation: this free inductor simulator works online in your browser, with live readouts beside the 3D model. Compare it with the capacitor simulator and the relay simulator. The glossary defines inductance.
Frequently asked questions
- What happens when an inductor saturates?
- Its core can no longer carry more magnetic flux, so the inductance drops sharply and the current rises much faster than the RL curve predicts. In a switching power supply that can mean a large current spike, overheating and a failed switch. Choose an inductor whose saturation current is above the peak current; you can set the saturation current in the simulator.
What you will learn
- Calculate the time constant τ = L/R and predict how changing inductance or series resistance speeds up or slows down the current rise.
- Predict the final DC current V/R and calculate the energy stored in the magnetic field with E = ½LI².
- Explain why core saturation lowers the effective inductance and makes the current rise faster than the ideal RL curve.
- Compare inductive reactance XL = 2πfL with the series resistance and calculate the impedance magnitude at a chosen frequency.
- Select a saturation current with margin above the final current by watching the near-saturation and saturated indications.
Model assumptions & references
Model assumptions and limitations
- The supply is an ideal DC voltage source switched onto an initially empty inductor. All resistance, winding plus any external resistor, is lumped into one series R (minimum 0.01 Ω), so the final current is V/R; negative voltages are treated as 0 V.
- The inductance is constant up to the saturation current, with no gradual roll-off before it. Above Isat it falls as L·(Isat/I)² but never below 10 % of L, the air-core limit. Above 80 % of Isat the state is flagged as near saturation.
- The current rise is computed by integrating L(i)·di/dt = V − R·i with a fourth-order Runge–Kutta method from zero current. Without saturation this reproduces I = (V/R)(1 − e^(−t/τ)).
- The displayed τ = L/R is the small-signal value using the nominal L. When the core saturates, the chart spans the time to reach 99 % of the final current and marks 63 % of it, instead of using 5 small-signal time constants.
- Stored energy is ∫L(i)·i di up to the final current: exactly ½LI² below Isat, numerically integrated above it, so in saturation it grows more slowly than ½LI² with the nominal L would suggest.
- Reactance and impedance use the nominal small-signal L and the DC resistance: XL = 2πfL and |Z| = √(R² + XL²). Saturation, parasitic capacitance, self-resonance and skin effect are not included in this read-out.
- The core is lossless and has no memory: inductance depends only on the current magnitude, so hysteresis, eddy-current and core losses, winding heating and temperature effects are not modelled.
References
- Engineering Circuit Analysis — William H. Hayt, Jack E. Kemmerly, Steven M. Durbin. Covers the RL step response, the time constant L/R, the energy stored in an inductor, and inductive reactance and impedance.
- The Art of Electronics — Paul Horowitz, Winfield Hill. Gives a practical treatment of inductors, reactance and impedance in real circuits.
- Fundamentals of Power Electronics — Robert W. Erickson, Dragan Maksimović. Explains magnetic core saturation, inductor design and energy storage in switching converters.