Curvo Studio

Part 2 · Chapter 11

RL time constant: how current rises in an inductor

The time constant of an inductor in series with a resistor is τ = L / R. When a voltage is applied, the current rises to 63.2% of its final value V/R after one τ and is practically settled after 5τ. With L = 100 mH and R = 24 Ω, τ = 4.17 ms.

Why current in an inductor rises gradually

An inductor opposes changes in current: the voltage across it is vL=L di/dtv_L = L \, di/dt. When a supply is first connected, the current is zero and the whole supply voltage appears across the inductor. As the current grows, more of the voltage drops across the resistance, less remains across the inductor, and the rate of rise slows.

The inductance LL and the series resistance RR set the pace. A large LL makes the current rise slowly; a large RR makes it settle sooner at a lower final value. It is the electrical twin of the RC time constant, with the roles of voltage and current swapped.

The RL formulas

Switching on a voltage VV across LL in series with RR, starting from zero current:

i(t)=VR(1−e−t/τ),vL(t)=V e−t/τ,τ=LRi(t) = \frac{V}{R}\left(1 - e^{-t/\tau}\right), \qquad v_L(t) = V\, e^{-t/\tau}, \qquad \tau = \frac{L}{R}

When the supply is replaced by a short, the current decays as i(t)=I0 e−t/τi(t) = I_0\, e^{-t/\tau}.

The percentages are the same as for the RC circuit: 63.2% after one τ\tau, 86.5% after two, 95.0% after three and 99.3% after five. The time constant L/RL/R is in seconds when LL is in henries and RR in ohms.

Worked example: L = 100 mH, R = 24 Ω, V = 12 V

1. Time constant: τ=0.1/24=4.17 ms\tau = 0.1 / 24 = 4.17\,\mathrm{ms}. 2. Final current: I=12/24=0.5 AI = 12 / 24 = 0.5\,\mathrm{A}. 3. Current after one τ\tau: 0.5×0.632=0.316 A0.5 \times 0.632 = 0.316\,\mathrm{A}. 4. Current after 5τ5\tau (20.8 ms): 0.5×0.993=0.497 A0.5 \times 0.993 = 0.497\,\mathrm{A}. 5. Time to reach 0.4 A (80%): t=−τln⁡(1−0.4/0.5)=4.17×1.61=6.7 mst = -\tau \ln(1 - 0.4/0.5) = 4.17 \times 1.61 = 6.7\,\mathrm{ms}. 6. Energy stored at the end: 12LI2=0.5×0.1×0.52=12.5 mJ\tfrac{1}{2} L I^2 = 0.5 \times 0.1 \times 0.5^2 = 12.5\,\mathrm{mJ}.

At the instant of switch-on the whole 12 V is across the inductor; at the end it is zero.

Switching off: why coils need protection

If the current path is opened suddenly, di/dtdi/dt becomes huge and the inductor produces a very large voltage spike in its attempt to keep the current flowing. This is the reason for the flyback diode across a relay coil, covered in the guide on relay drivers and flyback diodes. With the diode, the current decays through the loop with the same time constant L/RL/R instead of causing a spike.

The same L/RL/R time constant describes the electrical response of a motor winding, which is why a motor's current does not follow a voltage step at once.

Saturation changes the picture

The formulas assume a constant inductance. A real inductor with a magnetic core loses inductance when the current reaches its saturation value (see inductor saturation current). Past that point the current rises faster than the exponential predicts. In the example above, an inductor rated for only 0.4 A would saturate before the current settles, so the 0.5 A final value could not be assumed.

Try it in the inductor simulator

Open the inductor simulator. Set the Voltage, Inductance and Resistance and watch the RL current rise over 5τ.

  • Enter 12 V, 100 mH and 24 Ω and compare the curve with 0.316 A at one time constant.
  • Halve the Resistance: the final current doubles and τ\tau doubles.
  • Lower the saturation current below the final current and watch the curve depart from the ideal exponential.

Sources and further reading

  • C. K. Alexander and M. N. O. Sadiku, "Fundamentals of Electric Circuits", chapter on first-order circuits.
  • J. W. Nilsson and S. A. Riedel, "Electric Circuits", chapter on the natural and step responses of RL and RC circuits.
  • P. Horowitz and W. Hill, "The Art of Electronics", sections on inductors and inductive loads.

Try it in the simulator

Frequently asked questions

What is the RL time constant formula?
τ=L/R\tau = L / R, with LL in henries and RR in ohms, giving seconds. For 100 mH and 24 Ω it is 4.17 ms.
How long does it take for the current in an inductor to reach its final value?
About 5τ5\tau. After one τ\tau the current is at 63.2% of V/RV/R, and after five it is at 99.3%.
Why is the RL time constant L/R and not RL?
A larger inductance slows the current rise, while a larger resistance makes the current settle sooner because it limits the final value. So τ\tau grows with LL and shrinks with RR.
What happens when the current through an inductor is suddenly interrupted?
The inductor generates a large voltage spike, L di/dtL\,di/dt, to keep the current flowing. A flyback diode or snubber gives the current a safe path.