NPN Transistor Simulator: Ic–Vce Curves

An NPN bipolar junction transistor (BJT) is a current-controlled device in which a small base current controls a much larger collector current, IC=β IBI_C = \beta\,I_B. It has a cutoff, an active and a saturation region, and works as a switch or an amplifier. The Early effect adds a slight rise of ICI_C with VCEV_{CE}.

  • Power off
  • N region (emitter, collector)
  • P region (base)
  • Depletion layer
  • Electron flow
  • Drag to rotate

Parameters

Intrinsic parameters of the NPN transistor

Editable

Educational Ebers–Moll/Early model · Not a substitute for a manufacturer datasheet

Live values

Off

0.0 s

Operating regionPower off
Collector current0A
Base–emitter voltage0V
Power dissipation0W

Charts

Change IB and VCE to move the operating point and watch the transistor go from cutoff through the active region into saturation.

Output characteristics · IC–VCE

Curves at different base currents, with the maximum power limit

Transfer characteristic · IC–IB

Collector current against base current at the present VCE

See how a small base current controls a much larger collector current, and how the transistor moves from cutoff through the active region into saturation.

What is an NPN bipolar transistor?

A small current controlling a large one

An NPN bipolar junction transistor (BJT) is a current-controlled device in which a small base current controls a much larger collector current, IC=β IBI_C = \beta\,I_B. It has a cutoff, an active and a saturation region, and works as a switch or an amplifier. The Early effect adds a slight rise of ICI_C with VCEV_{CE}.

Reading the Ic–Vce family

Plotting collector current against Vce for several fixed base currents gives a family of curves. At low Vce the transistor is in saturation: both junctions are forward biased and Ic climbs steeply, with VCE(sat) usually 0.1–0.3 V. Past the knee it enters the active region, where Ic is nearly flat and set by β·Ib, the region used for amplification. With Ib = 0 only a tiny leakage current flows, which is cutoff.

Frequently asked questions

What is the difference between the active and saturation regions?
In the active region the collector-base junction is reverse biased, Ic is about β times Ib and nearly independent of Vce, so the transistor amplifies. In saturation both junctions are forward biased, Vce drops to about 0.1–0.3 V and Ic is set by the external circuit rather than by β, which is what a switch wants when it is on.

What you will learn

  • Explain how a small base current controls a much larger collector current through Ic = β·Ib in the active region.
  • Identify the cutoff, saturation and active regions on the Ic–Vce curves and locate the knee near VCE(sat).
  • Predict how lowering or raising the Early voltage VA changes the slope of the output curves and the output resistance ro ≈ VA/Ic.
  • Relate the Vbe readout to the base current and observe that it rises by only about 60 mV for each tenfold increase in Ib.
  • Assess whether an operating point is safe by comparing Vce·Ic with the maximum-power hyperbola Ic = Pmax/Vce.
Model assumptions & references

Model assumptions and limitations

  • The transistor is driven by an ideal base current source (0–200 µA) and Vce is applied directly (0–20 V); no base resistor, load resistor or load line is modelled, so Ic is never limited by an external circuit.
  • Collector current follows Ic = β·Ib·(1 + Vce/VA)·tanh(2·Vce/VCE(sat)); β and VA are constants that do not vary with current or temperature (clamped to β ≥ 1 and VA ≥ 1 V).
  • Below about 1.5 × VCE(sat) the tanh term rolls Ic smoothly down to zero at Vce = 0 and the region is labelled saturation; at 1.5 × VCE(sat) Ic is within 0.5 % of the active formula. VCE(sat) is clamped to at least 0.02 V.
  • Vbe comes from the ideal junction law VT·ln(β·Ib/Is) with fixed VT = 0.02585 V and Is = 10⁻¹⁴ A; it ignores temperature and the Early effect.
  • Cutoff leakage current is neglected: below Ib = 0.05 µA the transistor is only labelled cutoff, while currents and Vbe stay continuous. Junction breakdown is not modelled.
  • The dissipation Vce·Ic + Vbe·Ib is compared with a fixed Pmax and only triggers an overload warning; self-heating, thermal runaway and temperature derating are not simulated.
  • The model is static DC: junction capacitances, transit times and frequency response are absent, and the transconductance gm = Ic/VT is computed only in the active region.

References

  • Microelectronic Circuits — Adel S. Sedra, Kenneth C. Smith. Covers BJT operating regions, the Ic = β·Ib relation, the Early effect and the small-signal transconductance used in this simulator.
  • The Art of Electronics — Paul Horowitz, Winfield Hill. Gives practical guidance on using transistors as switches and amplifiers, including saturation, base drive and power dissipation limits.
  • Large-Signal Behavior of Junction Transistors — J. J. Ebers, J. L. Moll. Introduces the large-signal junction-transistor model from which the simplified current and Vbe relations in this simulator are derived.
  • Effects of Space-Charge Layer Widening in Junction Transistors — J. M. Early. Explains the base-width modulation that produces the Early effect and the upward slope of the output curves.